Buying advice

Do You Need a Vapour Barrier Under Vinyl Plank or Laminate on a Basement Slab in Ontario?

A poly vapour barrier and the pad on a vinyl plank do different jobs. See what laminate and SPC installation instructions ask for on a basement slab, and why the moisture reading comes first.

Driftwood Mist 8mm SPC vinyl plank flooring photographed flat, light taupe oak grain
Driftwood Mist 8mm SPC vinyl plank flooring photographed flat, light taupe oak grain
In this article

A poly vapour barrier and the pad bonded to the back of a vinyl plank do different jobs. Whether your basement slab needs a barrier depends on the floor you pick and on what the concrete underneath is doing. Swiss Krono, one of the laminate makers we carry, requires a vapour barrier on concrete before the underlay goes down. For floating SPC vinyl, Shaw's published SPC installation guideline recommends 6 mil poly film over concrete, and the slab has to meet its moisture limits first. Here's how we work through it, from moisture reading to finished floor, using specs and prices from our vinyl plank collection and one laminate.

The short answer for a basement slab

  • An attached pad isn't a vapour barrier. The three SPC planks below are sold on the comfort and sound of their pads (one also mentions moisture protection). None of them calls the pad a vapour barrier or vapour retarder.
  • Swiss Krono laminate on concrete gets a barrier first. Swiss Krono requires a vapour barrier on a mineral subfloor before the impact and sound underlay goes down.
  • Floating SPC depends on the slab test. Shaw's SPC guideline recommends poly film for floating installs over concrete and sets maximum readings for two ASTM moisture tests.
  • A reading over the limit stops the job. Shaw calls for moisture mitigation on existing concrete when results exceed product limitations, so the moisture gets fixed before the barrier question even comes up.

If you're budgeting for the whole basement and not just this one detail, our flooring installation cost guide for Toronto explains how installation is priced for each flooring type.

Why the slab reading comes before the barrier

Installation instructions name two ASTM tests for concrete, and they report different numbers. ASTM F2170 uses in situ probes to measure percent relative humidity inside the slab. ASTM F1869, the calcium chloride test, measures how much moisture vapour bare concrete gives off, in pounds over a 1000 sq ft area during 24 hours.

Here's why it matters. According to F2170, too much moisture in a slab once a floor covering is down "can cause floor covering system failures such as debonding, peaking and deterioration of finish flooring and coatings". That's why flooring manufacturers generally require a moisture test before installing on concrete.

Every result is a snapshot. It shows the slab's condition "only at the time of the test and in the specific locations tested", so an old reading tells you little about install day. Our guide to moisture testing concrete subfloors explains how each test is set up and read.

What each floating floor needs over a basement slab

All four floors below are click-lock floating floors from our catalogue. Three are SPC vinyl planks with a factory-attached pad, and one is a laminate that takes a separate underlay. Each is sold by the box, and the last column sums up the manufacturer slab guidance we quote further down.

Product Box price Coverage per box Material per sq ft Total thickness Wear layer or rating Attached pad Published slab guidance
Driftwood Mist SPC $59.00 16.55 sq ft $3.56 8mm 20mil EVA Poly film recommended in Shaw's general SPC guideline (not a Riche document)
Greige Oak SPC $59.00 11.82 sq ft $4.99 10mm 20mil EVA As above (Shaw benchmark)
Blonde Sand Oak SPC $62.93 23.64 sq ft $2.66 6mm 12mil IXPE As above (Shaw benchmark)
Swiss Krono Grey Oak laminate $42.83 17.22 sq ft $2.49 10mm AC5 None listed Vapour barrier required before the underlay (Swiss Krono)

Prices checked October 6, 2026. Box prices and coverage are from our current catalogue.

Thickness and wear layer tell you about the plank, not the slab. Driftwood Mist's total thickness, for example, is the SPC core plus the attached EVA pad. Neither number changes what the concrete underneath needs, so the last column comes from installation instructions.

Driftwood Mist 8mm SPC vinyl planks photographed flat, showing light taupe oak grain across three boards
Driftwood Mist: heavy-duty 8mm SPC with a 20mil wear layer, at $3.56/sq ft.

SPC vinyl with a factory-attached pad

All three SPC planks come with a pad bonded at the factory: EVA on Driftwood Mist and Greige Oak, IXPE on Blonde Sand Oak. Driftwood Mist's pad gives a cushioned feel and reduces sound. Blonde Sand Oak's adds comfort, thermal insulation and noise reduction. Greige Oak's offers cushion, sound absorption and moisture protection. None of the three is described as a vapour barrier or retarder.

For the slab, Shaw Industries' generic SPC installation guideline makes a useful benchmark. It says 6 mil poly film underlayment "is recommended for floating method over concrete substrates", but it treats the film as an extra layer, not a fix: "For existing concrete substrates with high moisture, moisture mitigation will need to be completed if testing results exceed product limitations."

Shaw also puts numbers on those limits: "maximum moisture level per ASTM 1869 CaCl is 8 lbs. and ASTM 2170 In-situ Relative Humidity 90% per 1000 sq.ft. in 24 hours". It also says not to install over concrete with a history of high moisture or hydrostatic conditions. Limits vary from one manufacturer to the next, so check your reading against the instructions for the exact plank you buy.

Blonde Sand Oak is the lowest-priced of the three at $2.66 per sq ft, with a 12mil wear layer and 23.64 sq ft per box. Its slim 6mm profile helps in renovations where the transition height to the next floor matters. Greige Oak sits at the top end: $4.99 per sq ft for a 10mm plank with a 20mil wear layer.

Blonde Sand Oak 6mm SPC planks photographed flat, pale golden oak grain with one end joint visible
Blonde Sand Oak: 6mm SPC with an IXPE pad, at $2.66/sq ft ($62.93 per 23.64 sq ft box).

Does SPC need extra underlayment at all? That's a separate question, and our underlayment guide for SPC vinyl answers it.

Laminate over a slab

Swiss Krono is clear about concrete and screed: "A vapor barrier must be installed on a mineral sub-floor before the impact and room sound underlay is laid." Its vapour barrier page explains why: "If laminate flooring is permanently exposed to rising moisture, it swells and causes irreparable damage." Swiss Krono recommends a vapour barrier on mineral subfloors such as concrete and screed because these floors release moisture.

Basements come with extra conditions. The slab "must have been poured with a poly sheet underneath it" and must be more than 90 days old so it has properly cured. If the floor has a drain, or a French drain running along the inside of the perimeter, Swiss Krono doesn't recommend laminate. For cement screed, the maximum residual moisture is 2.0 CM%. Our 10mm Grey Oak laminate is AC5 rated and covers 17.22 sq ft per box at $42.83.

Swiss Krono Grey Oak laminate on a showroom display board, knotted grey oak grain with a product label
Swiss Krono Grey Oak laminate, 10mm and AC5 rated, at $2.49/sq ft. It's the floor in the table that requires a vapour barrier on concrete.

When the slab reading is over the limit

If your reading is above the limit in your product's instructions, the floor has to wait, whatever material you chose. The season matters too. Swiss Krono warns that a subfloor that seems dry in summer might be completely different in winter, so test close to install day.

Here's the order we follow.

  1. Deal with the water first. Natural Resources Canada suggests a simple check: tape a sheet of plastic to the slab and look underneath after a day or two. Condensation under the plastic means moisture is moving up from the ground. NRCan says any renovation after that will need remediation for the damp, such as concrete sealing or waterproofing and subfloor membranes.
  2. Price mitigation separately. Moisture mitigation and subfloor work aren't part of a per-square-foot floor rate. We quote them once we've seen the slab.
  3. Rethink the floor type. If the room can't meet Swiss Krono's basement conditions, that laminate isn't an option there. For vinyl, go by the limits in the plank's own installation instructions.
  4. Check your building's rules. In a condo or shared building, find out what's allowed before you order.

Membranes, coatings and combination underlays are chosen by whoever does the slab work, and we don't stock them. Our guide to moisture barriers over concrete explains where each type fits, and our complete guide to basement flooring in Toronto covers the rest of the room.

How we plan a basement install around slab moisture

To price a basement, we need your room sizes, building type, current floor and whatever you know about the slab: how old it is, whether there's a poly sheet under it, and any test result along with the method used. We quote levelling, subfloor repair and moisture mitigation after we've seen the space, because the slab's condition decides how much prep the job needs.

We supply and install click-lock SPC vinyl and laminate, and we settle the slab question before the floor gets ordered. If a reading is close to a limit, get a proper test instead of buying a barrier on a guess.

Basement vapour barrier FAQ

Do I need poly under vinyl plank on a basement slab?

For floating SPC, Shaw's guideline recommends 6 mil poly on concrete, but the film only helps once the slab is within its moisture limits. Check your plank's instructions, because limits vary by manufacturer.

Is the attached pad on SPC enough on concrete?

Not as a vapour barrier. The three SPC planks above use their pads for cushioning and sound control. Greige Oak mentions moisture protection, but even it doesn't call its pad a vapour retarder. Think of the pad as part of the plank and deal with the slab on its own terms.

Does a waterproof plank keep slab moisture out?

Waterproof describes the plank. Greige Oak's rigid core "will not swell, warp, or buckle from moisture exposure", and Blonde Sand Oak "will not swell, warp, or buckle when exposed to water". Vapour rising through a slab is a different issue, and ASTM F1869 notes that all concrete subfloors emit some amount of moisture in vapour form.

How do I know if my basement slab is dry enough for flooring?

Compare a measured result with the limit in your product's instructions. Manufacturers name ASTM F2170, which gives relative humidity as a percentage, and ASTM F1869, which gives pounds of vapour. Use whichever method your instructions accept. The plastic-sheet check shows whether moisture is moving, but it won't give you a number to compare.

My slab has been dry for years. Do I still need a barrier?

For Swiss Krono laminate, yes. The manufacturer requires one on mineral subfloors and notes that it's often advisable even for floors that look dry at first sight. For SPC, go by a current test, not the slab's history.

Get a basement flooring quote in Toronto and the GTA

Send us your room sizes, building type and what you know about the slab, and we'll price the floor and its installation to suit. You can request a basement flooring quote online.

Top Floorings Depot
3781 Victoria Park Avenue, Unit 1, Toronto, ON M1W 3K5
www.topfloorings.com
Call: 416-499-0117
Text: 416-770-8819

Back to Flooring Guides