If a laminate or vinyl plank won't lock, or a joint springs apart while you're laying the next board, stop pushing. Separate the joint and check its profile, the previous row and the subfloor. That's usually where you'll find the cause. This checklist covers problems during installation, not seams that open later. Browse our laminate collection for examples, but always follow the instructions for your exact floor.
Quick answer: pause and find the reason
When a click joint won't engage, check the setup. Don't add force. First work out which edge is failing: the long side or the short end. Then inspect both mating edges, confirm the plank is facing the right way, and make sure the row you're joining is straight and fully connected. A joint can look closed from above and still be sitting high or partly open.
If a board is chipped, crushed or misshapen at its locking edge, set it aside. The next plank won't pull it into place. If several boards fail in the same spot or the same way, stop and recheck your joining method, your alignment and the surface underneath. Carrying on past a bad connection makes it harder to find where the problem started.
A board that never locks during installation is a different problem from a seam that separates after the floor has been in use. For that one, see our guide to laminate seams that open after installation.
Start with the joint's intended motion
“Click-lock” covers a whole family of joints, not one single movement. Some profiles engage when you angle a plank into the previous row. Others fold down, press down or connect horizontally. You can't swap one motion for another. Check the product instructions and follow the sequence they show for the long edge and the end joint separately.
Angle and lower
With an angle-style connection, you set the tongue into the groove at an angle and lower the plank only once the edges line up. Goodfellow's Floorpan Elite XL instructions put it this way: “Position the tongue of the plank at a 20-30° angle into the groove of the plank in the previous row. Lower the plank until the long side locks securely.” That angle is for that product, not for every laminate or vinyl floor. If you're installing that collection, read the Goodfellow installation instructions.
Välinge's 2G system engages by angling the panels, and its 5G system folds down. 5G-i uses an angled long side followed by a push down. So the motion depends on the profile, not on whether the floor is laminate or vinyl. Shown here is a Grey Oak laminate from our catalogue, sold as click-lock.
Fold down, press or connect horizontally
Some joints fold down. Others snap, press down or connect horizontally. Unilin says its Unifit profile can go in with a drop-down, angled or horizontal snap-or-tap method. Even with a flexible profile like that, don't guess. Use the method specified for your exact plank and the edge you're joining.
If you can't find the instructions for your model, don't copy the motion from a product that just looks similar. Compare the groove and tongue with an unused plank from the same box, and ask the retailer or manufacturer to confirm the right motion before you continue. Don't glue, tap or strike a joint unless the instructions call for it.
Check the five likely trouble spots
Debris in the profile
Look along the whole groove and tongue in good light. A shaving, some grit or a loose fragment can stop two edges from meeting flush. Brush or vacuum it away and look again. Don't dig at the profile with a hard tool, because it's easy to damage the locking lip. Check the floor right around the joint too, so nothing gets trapped under the plank.
A crooked or partly open row
Don't look only at the new plank. Follow the joint back along the row. If an earlier connection is open, raised or out of line, the new edge can't meet its mate squarely. Separate the new plank using the product's approved removal method, then find and fix the first incomplete connection. Once a row starts to drift, every joint after it gets harder to engage.
Sight along the row from a low angle and run your hand over it to feel for a raised edge or a gap. If it won't sit straight, recheck your starting position and fix any earlier joint before moving on. Don't force the next board to close a gap.
A hump, dip or loose layer underneath
A plank that rocks or bridges a hollow can't settle into its neighbour. Make sure the surface is clean, stable and flat enough for your floor. Look for ridges, soft or moving spots in the subfloor, or a loose layer under the joint. Even a small obstruction can change how a plank sits, and a larger uneven area needs fixing before you go on. Never try to pull a joint together over a surface problem.
Flatness tolerances vary by manufacturer and product, so don't use one floor's number for another. Our subfloor flatness guide covers manufacturer tolerances in more detail. The practical rule is simple: if a board rocks, tips or won't lie flush, check the surface before you continue.
A chipped tongue or damaged groove
Check the short end as closely as the long edge. A cracked locking lip, a crushed corner or a bent groove can make a board impossible to seat. Compare it with an unused plank from the same box. If you can see the damage, stop trying. Set the board aside and follow the supplier's process for reporting or replacing it. Don't cut away or reshape the locking edge unless the instructions tell you to.
A product or box mismatch
If a connection looks different from the boards around it, check the box label and the plank markings. Similar-looking boards can have different profiles or come from different products. Don't mix in leftovers or a replacement plank just because the colour is close. Make sure the product codes and edge shapes match before you try again.
Here's a useful test. If a new plank connects to an unused matching board but not to the laid row, look at the alignment and the earlier joints in that row. If it won't connect to several matching boards laid flat in a clean area, look at the joining sequence or the plank itself. Keep the labels and take photos of any suspect edge. They help the supplier identify what you're working with.
What these laminate and vinyl planks cost
Our catalogue has both laminate and click-lock vinyl at a range of prices per square foot. Whatever you spend, never force a damaged or unsuitable joint, and follow the installation guide for the floor you choose. For more on brands, see our AC5 laminate brand guide.
| Product | Type | Box price | Coverage | Price per sq ft |
|---|---|---|---|---|
| Swiss Krono Grey Oak | Laminate | $42.83 | 17.22 sq ft | $2.49 |
| Egger EM7206 | Laminate | $40.48 | 21.42 sq ft | $1.89 |
| Goodfellow Prag | Laminate | $60.54 | 20.18 sq ft | $3.00 |
| Nordic Frost | Laminate | $69.99 | 15.4 sq ft | $4.54 |
| Sahara Shore | Vinyl plank | $59.00 | 16.55 sq ft | $3.56 |
Prices checked October 7, 2026. Price per square foot is the box price divided by the box coverage, rounded to the nearest cent. See the Nordic Frost product page for details, or our German laminate brand comparison for a wider selection.
On the vinyl side, Riche Flooring's Sahara Shore is a click-lock plank with a 20mil wear layer. Don't assume a vinyl plank and a laminate plank share the same edge profile or installation motion.
Whether you're choosing material or troubleshooting a new install, keep the packaging and the instructions together. If your floor is lifting after installation instead, read our vinyl lifting troubleshooting post.
Floors that look alike can still have different locking profiles.
When to stop instead of forcing a joint
Stop if the edge is visibly damaged, if the plank won't sit flush, or if the instructions are missing or unclear. Stop as well if the same problem keeps happening on matching boards. More attempts at that point only make it harder to tell whether the cause is a damaged profile, the wrong method or the surface underneath.
Keep the box label, the affected plank and photos of the edge. Ask the seller or manufacturer for the correct joining method and the approved way to remove or replace boards. Don't borrow instructions from another system. If a seam opens after installation, that's a different problem and needs a different fix.
Laminate and vinyl plank clicking questions
Why won't my laminate click together at the short end?
The end joint may need a different motion from the long side. Check the instructions for the short edge, look in the groove for debris or damage, and make sure the adjoining row is lined up. If the edge is chipped or doesn't match the other boards, stop and contact the seller before you go further.
Can I keep installing if the joint will not lock?
Stop at the joint that failed. Check the profile, alignment and surface, and carry on only once the joint engages using the product's specified method and lies flush. If you build past an open or raised joint, the misalignment can carry into the next row.
Should I hammer or tap a plank that will not click?
Only if the instructions for that exact product call for a tapping tool and explain where and how to use it. Some joints are made to angle and lower or to press down, and a tapping method meant for another product can damage them.
Why does vinyl plank keep separating during installation?
Check that the row is straight and fully engaged, that the board isn't rocking on an uneven spot, and that your motion matches the vinyl product's instructions. Don't force a plank that keeps springing away. The cause may be alignment, the surface or a damaged connection, not the fact that it's vinyl.
Get a flooring quote in Toronto and the GTA
If you're replacing boards or choosing flooring for a project, send us the product name and room details. Request a flooring quote and we'll help you work out the next step.
Top Floorings Depot
3781 Victoria Park Avenue, Unit 1, Toronto, ON M1W 3K5
www.topfloorings.com
Call: 416-499-0117
Text: 416-770-8819